BLOOD COLLECTION TUBE

product information BLOOD COLLECTION TUBE

Microcollect & Specimencollect

consists of tube parts made of polypropylene and cap parts applied with international standard color. Each tube is marked with a dose scale line for collecting the appropriate amount of blood, and inside the tube is finely coated with anticoagulant and clot activator.

How to use

  • 1) Prepare a separate Lancet.
  • 2) Stab the peripheral blood vessel position at the tip of the finger or heel.
  • 3) Remove the caps of the product, visually verify that blood enters the tube through the blood induction(Lip) at the entrance of the tube, and whether the amount of blood is appropriate(250~500㎕) for examination, then re-cap it and store it or conduct the necessary examination.
  • 4) Conduct a blood analysis according to the normal and discard it.
  • 5) This product is intended for single use, and if further inspection is required, repeat paragraph (1).

Precautions for Use

  • 1) It is a disposable product and should not be reused.
  • 2) It is a disposable product and should not be reused.
  • 3) Use only for in vitro diagnosis.
  • 4) After use, dispose of the waste in a waste box according to the prescribed method.
  • 5) Store in a place free from direct sunlight and moisture.

Serum Plain Tube

  • #111105
  • #111124

Serum tube is coated with silicon and micronized silica particles to rapidly activate the coagulation process by gently conducting mixing 8 to 10 times for serum measurement in biochemistry. Specially developed components on the wall make serum tubes reduce adherence of red blood cells to tube wall. Samples processed in these tubes may also be used for routine blood screening, immunohematology, and diagnostic testing of serum for infectious disease.

Product code Blood collection Standard(mm) Additive reagent Packing unit
111105 250~500㎕ 10x45 Clot Activator 50/200
111124 4ml 13x75 25/100

Serum Separation Gel Tube

  • #111205
  • #111223

Serum with Gel contains a barrier polymer in the base of the tube and this material causes it to move upward to serum-clot interface forming a stable separation barrier during centrifugation. Serum may be aspired directly from the collection tube eliminating the need for manual transfer to another container. In the primary tube and under recommended laboratory conditions, certain parameters remain stable for up to 48 hours.

Product code Blood collection Standard(mm) Additive reagent Packing unit
111205 250~500㎕ 10x45 Clot Activator with Gel 50/200
111223 3.5ml 13x75 25/100

Coagulation Tube

  • #164101

Coagulation tubes are used for examination of coagulation parameters. Coagulation tubes contain a buffered sodium citrate solution.It is available with a citrate concentration of 0.109 mol/l (3.2%) or 0.129 mol/l (3.8%). The choice of the concentration depends on the policy of the laboratories. The mixing ratio is 1part citrate solution to 9 parts blood.

Product code Blood collection Standard(mm) Additive reagent Packing unit
164101 250~500㎕ 10x45 Sodium citrate 3.2% 50/200

EDTA Tube

  • #122105
    #123105
  • #123124

EDTA Tubes are coated with K2-EDTA or K3-EDTA for blocking coagulation cascade by binding calcium ions in the blood sample. EDTA tubes must be inverted 8-10 times to assure complete mixing with blood for correct coagulation value. EDTA Tubes are used for direct sampling analysis since erythrocytes and leucocytes are stable for 24 hours with EDTA while thrombocytes are stable for 6-8 hours. Blood smearing should be done within 3 hours after blood collection. EDTA tubes are for the examination of whole blood in hematology.

Product code Blood collection Standard(mm) Additive reagent Packing unit
122105
123105 		250~500㎕ 10x45 K2&K3 EDTA 50/200
123124 4ml 13x75 25/100

Plasma Tube

  • #126105

Plasma tubes are coated with lithium heparin or sodium heparin to inhibit clotting. Heparin activates antithrombin, thus blocking the coagulation cascade and producing a whole blood/plasma sample instead of clotted blood and serum. Lithium determination should not be performed in lithium heparin tubes. Samples collected in these tubes are used for plasma determinations in chemistry.

Product code Blood collection Standard(mm) Additive reagent Packing unit
126105 250~500㎕ 10x45 Lithium heparin 50/200

Plasma Separation Gel Tube

  • #126205

Plasma tubes with gel contain spray-coated lithium heparin and a polymer gel in the bottom for plasma separation. The specific gravity of this material can make the barrier gel move upward to the plasma-clot interface during centrifugation and it forms a stable barrier separating the plasma from cells. Samples processed in these tubes are used for plasma determinations in chemistry. Those tubes provide the convenience of gel separation with the added advantage of improved turnaround time.

Product code Blood collection Standard(mm) Additive reagent Packing unit
126205 250~500㎕ 10x45 Lithium heparin with Gel 50/200